1.5L Hydrogen Water Bottle Hydrogen Rich Portable Rich Hydrogen Water Generator

Product Specification body { font-family: Arial, sans-serif; font-size: 13.5px; } p { margin: 0 0 1em; } Specification Material: PC Dimensions: 22x12x12cm Capacity: 1.5L Hydrogen concentration: 1200ppb-2400ppb Battery capacity: 1500mAh Hydrogen production time: 6 minutes Number of hydrogen production: 10 times Charging method: USB Instructions: 1. Before use, test the water first. As the pot body and lower base are separate, water leakage may occur during transportation due to bumps. Unscrew the base, check the rubber pad, and tighten it again. 2. Do not use hot water above 80 degrees Celsius. It is best to rinse twice with water at 50 degrees Celsius to achieve 40 degrees Celsius. Otherwise, if it exceeds 45 degrees Celsius, hydrogen will evaporate immediately. 3. It is recommended to use water containing minerals for the best results. Beverages excluded. 4. Do not approach the ignition source during hydrogen production. 5. The number of hydrogen production times should not be too high (1-2 times is the best) to prevent the pressure from being too high, which may cause the base to leak. 6. When producing hydrogen, when the milky white bubbles dissipate, it should be consumed for about 2 minutes before drinking. The taste is better. 7. When it is found that the bubbles in the water have decreased and there is dirt on the pot body, it can be poured into white vinegar, covered and soaked for more than 2 hours, shaken for another 2 minutes, and washed clean with water. 8. Remember not to burn dry. Otherwise, hydrogen will not be produced. The base is burnt out. 9. When carrying it with you, please tighten the cup cover clockwise to avoid leakage. 10. Do not use volatile agents, gasoline, metal wire balls, or hard objects to clean the product to avoid scratching the pot body. 11. If you forget to drink after electrolysis, you can repeat electrolysis to increase the hydrogen content in the water for better results. 12. When cleaning the bottom, it is necessary to use a soft sponge basket, cloth, or soft brush to wipe it clean and keep the bottom dry. 13. When charging, the green light will flash, and after the charging is completed, the green light will stop flashing. Charging once takes 12 hours, and fully charging can produce about 5-6 pots of hydrogen rich water. Due to objective reasons such as water quality and climate in different regions, the number of cups made and charging time may also vary. 14. The hydrogen production time is 10 minutes at a time. After the hydrogen production is completed, the machine will automatically shut down. The blue light of the button will light up during hydrogen production. To forcibly shut down, press the button. Notice: 1. Due to the influence of many factors such as display brightness and light brightness, the actual color of the item may be slightly different from the image displayed on the website. 2. Please allow slight differences in data from manual measurement. Package includes: Portable pot*1 1. Before use, test the water first. As the pot body and lower base are separate, water leakage may occur during transportation due to bumps. Unscrew the base, check the rubber pad, and tighten it again. 2. Do not use hot water above 80 degrees Celsius. It is best to rinse twice with water at 50 degrees Celsius to achieve 40 degrees Celsius. Otherwise, if it exceeds 45 degrees Celsius, hydrogen will evaporate immediately. 3. It is recommended to use water containing minerals for the best results. Beverages excluded. 4. Do not approach the ignition source during hydrogen production. 5. The number of hydrogen production times should not be too high (1-2 times is the best) to prevent the pressure from being too high, which may cause the base to leak. 6. When producing hydrogen, when the milky white bubbles dissipate, it should be consumed for about 2 minutes before drinking. The taste is better. 7. When it is found that the bubbles in the water have decreased and there is dirt on the pot body, it can be poured into white vinegar, covered and soaked for more than 2 hours, shaken for another 2 minutes, and washed clean with water. 8. Remember not to burn dry. Otherwise, hydrogen will not be produced. The base is burnt out. 9. When carrying it with you, please tighten the cup cover clockwise to avoid leakage. 10. Do not use volatile agents, gasoline, metal wire balls, or hard objects to clean the product to avoid scratching the pot body. 11. If you forget to drink after electrolysis, you can repeat electrolysis to increase the hydrogen content in the water for better results. 12. When cleaning the bottom, it is necessary to use a soft sponge basket, cloth, or soft brush to wipe it clean and keep the bottom dry. 13. When charging, the green light will flash, and after the charging is completed, the green light will stop flashing. Charging once takes 12 hours, and fully charging can produce about 5-6 pots of hydrogen rich water. Due to objective reasons such as water quality and climate in different regions, the number of cups made and charging time may also vary. 14. The hydrogen production time is 10 minutes at a time. After the hydrogen production is completed, the machine will automatically shut down. The blue light of the button will light up during hydrogen production. To forcibly shut down, press the button.